2.8-inch 240x320 tft displayer，sunlight readable display
2.8-inch, resolution 240×320, SPI interface, TN display mode, the best Angle of view 6 o ‘clock, 800cd/㎡, high brightness display.
Main parameters of 2.8-inch tft display
| ITEM | Standard value | UNIT |
| LCD SIZE | 2.8 | INCH |
| LCD Type | Normally white | — |
| Driver Element | a-Si TFT Active matrix | — |
| Number of Dots | 240*(RGB)*320 | Dots |
| Pixel Arrangement | RGB Vertical Stripe | — |
| Pixel Pitch (W*H) | 0.153*0.153 | mm |
| Active Area | 43.2*57.6 | mm |
| Glass Area (W*H) | 46.2*64.75 | mm |
| Viewing Direction | 12 O’clock | — |
| Control IC | ST7789V | — |
| Module Size(W*H*T) | 50.0(W)*69.2(L)*2.3(H) | mm |
| Approx. Weight | TBD | g |
| Back Light | White LED | |
Download relevant technical documents
Customize the length, width and thickness of FPC or cable, adjust the pin arrangement according to the interface type, and select the appropriate connector. Make your display or circuit board simple and safe with an excellent FPC solution.
A touch screen can be added according to your requirements, there are three options: resistive touch screen, capacitive touch screen, infrared touch screen. Or add protective glass as needed
Display screens with different optical parameters can be designed according to needs, such as brightness, color gamut, response time, gamma and other parameters, and anti-glare, anti-fingerprint coatings, etc. can also be added
The circuit board we designed can convert the interface of your display into an HDMI interface. If your product does not have any display control capabilities, you can use our serial display and only need to use simple commands to control the displayed content through RS232/458
2.8-inch tft display drawings and interfaces
2.8-inch, resolution 240×320, TN display mode, the best Angle of view 6 o ‘clock, MCU 8/16 Bit /SPI 3L/SPI 4L interface can be selected, the backlight adopts 4 LED in parallel, the working voltage is 2.8-3.3V, Current 120mA,800cd/㎡, 2.8in, resolution 240×320, SPI interface, TN display mode, the best Angle of view 6 o ‘clock, MCU 8/16 Bit /SPI 3L/SPI 4L interface can be selected, the backlight adopts 4 LED in parallel, the working voltage is 2.8-3.3V, Current 120mA,brightness is 800cd/㎡, high brightness display, ZIF connector. ZIF connector.
The outline drawing is as follows:
Interfaces are defined as follows：
| Pin | Symbol | Detail |
| 1 | GND | GROUND |
| 2 | NC | |
| 3 | NC | |
| 4 | NC | |
| 5 | NC | |
| 6 | NC | |
| 7 | VCI | Analog Power |
| 8 | IOVCC | Logic Power |
| 9 | NC | |
| 10 | CS | Chip select input pin |
| 11 | RS | Display data/command selection pin in parallel interface. This pin is used to be serial interface clock. |
| 12 | WR | Write enable in MCU parallel interface Display data/command selection pin in 4-line serial interface |
| 13 | RD | Read enable in 8080 MCU parallel interface.If not used, please fix this pin at GND |
| 14 | DB0 | Data Bus.If not used, please fix this pin at GND |
| 15 | DB1 | |
| 16 | DB2 | |
| 17 | DB3 | |
| 18 | DB4 | |
| 19 | DB5 | |
| 20 | DB6 | |
| 21 | DB7 | |
| 22 | DB8 | |
| 23 | DB9 | |
| 24 | DB10 | |
| 25 | DB11 | |
| 26 | DB12 | |
| 27 | DB13 | |
| 28 | DB14 | |
| 29 | DB15 | |
| 30 | RESET | RESET pin |
| 31 | IM0 | MCU interface mode select. |
| 32 | NC | |
| 33 | GND | |
| 34 | LEDK | LED Cathode |
| 35 | LEDK | |
| 36 | LEDK | |
| 37 | LEDK | |
| 38 | LEDA | LED Anode |
| 39 | GND | GROUND |
| 40 | NC |
