2.0-inch 240x320 tft display, sunlight readable display
2.0-inch 240×320, IPS display, MCU and three-wire/four-wire SPI interface can be selected, high brightness display, brightness up to 600cd/㎡.
Main parameters of 2.0-inch tft display
| ITEM | Standard value | UNIT |
| LCD SIZE | 2.0 | INCH |
| LCD Type | TFT Negative Transmissive | — |
| Driver Element | a-Si TFT Active matrix | — |
| Number of Dots | 240*(RGB)*320 | Dots |
| Pixel Arrangement | RGB Vertical Stripe | — |
| Pixel Pitch (W*H) | 0.219*0.219 | mm |
| Active Area | 30.60(H) *40.80(V) | mm |
| Viewing Direction | all view direction | — |
| Control IC | ST7789 | — |
| Module Size(W*H*T) | 35.70(H) ×51.20(V)× 2.30(D) | mm |
| Back Light | White LED | |
Download relevant technical documents
Customize the length, width and thickness of FPC or cable, adjust the pin arrangement according to the interface type, and select the appropriate connector. Make your display or circuit board simple and safe with an excellent FPC solution.
A touch screen can be added according to your requirements, there are three options: resistive touch screen, capacitive touch screen, infrared touch screen. Or add protective glass as needed
Display screens with different optical parameters can be designed according to needs, such as brightness, color gamut, response time, gamma and other parameters, and anti-glare, anti-fingerprint coatings, etc. can also be added
The circuit board we designed can convert the interface of your display into an HDMI interface. If your product does not have any display control capabilities, you can use our serial display and only need to use simple commands to control the displayed content through RS232/458
2.0-inch TFT LCD Display drawings and interfaces
2.0 “240×320, IPS display, MCU and three-wire/four-wire SPI interface can be selected, 4 LED beads in parallel, working voltage 3.2V, current 80mA, brightness up to 600cd/㎡, need to pay attention to power consumption when elected to use high brightness display.
2.0-inch 240x320 tft display video
The outline drawing is as follows:
Interfaces are defined as follows：
| Pin | Symbol | Detail |
| 1 | GND | GROUND |
| 2 | NC | let this pin open |
| 3 | NC | |
| 4 | NC | |
| 5 | NC | |
| 6 | SDO | SPI interface output pin.If not used, let this pin open. |
| 7 | VCI | Analog Power |
| 8 | IOVCC | Logic Power |
| 9 | SDA | SPI interface input pin.If not used, please fix this pin at GND. |
| 10 | CS | Chip select input pin |
| 11 | RS | Display data/command selection pin in parallel interface. This pin is used to be serial interface clock. |
| 12 | WR | Write enable in MCU parallel interface Display data/command selection pin in 4-line serial interface |
| 13 | RD | Read enable in 8080 MCU parallel interface.If not used, please fix this pin at GND |
| 14 | DB0 | Data Bus.If not used, please fix this pin at GND |
| 15 | DB1 | |
| 16 | DB2 | |
| 17 | DB3 | |
| 18 | DB4 | |
| 19 | DB5 | |
| 20 | DB6 | |
| 21 | DB7 | |
| 22 | DB8 | |
| 23 | DB9 | |
| 24 | DB10 | |
| 25 | DB11 | |
| 26 | DB12 | |
| 27 | DB13 | |
| 28 | DB14 | |
| 29 | DB15 | |
| 30 | RESX | Reset Pin |
| 31 | IM0 | MCU interface mode select. |
| 32 | NC | |
| 33 | GND | Ground |
| 34 | LED_K | LED Cathode |
| 35 | LED_K | |
| 36 | LED_K | |
| 37 | LED_K | |
| 38 | LED_A | LED Anode |
| 39 | GND | GROUND |
| 40 | NC |
