1.44-inch 128x128, sunlight readable display
1.44-inch 128×128 resolution, supporting 3-wire or 4-wire SPI interface and MCU interface, brightness up to 500cd/㎡, sunlight readable display
The main parameters of the 1.44-inch high brightness display
| ITEM | Standard value | UNIT |
| LCD SIZE | 1.44 | INCH |
| LCD Type | TFT Negative Transmissive | — |
| Driver Element | a-Si TFT Active matrix | — |
| Number of Dots | 128*(RGB)*128 | Dots |
| Pixel Arrangement | RGB Vertical Stripe | — |
| Pixel Pitch (W*H) | 0.219*0.219 | mm |
| Active Area | 25.498(H) *26.496(V) | mm |
| Viewing Direction | Optimal Viewing Angle 6 o ‘clock | — |
| Control IC | ST7735 | — |
| Module Size(W*H*T) | 29.5(W)*35.5(L)*2.5(H) | mm |
| Back Light | White LED | |
Download relevant technical documents
Customize the length, width and thickness of FPC or cable, adjust the pin arrangement according to the interface type, and select the appropriate connector. Make your display or circuit board simple and safe with an excellent FPC solution.
A touch screen can be added according to your requirements, there are three options: resistive touch screen, capacitive touch screen, infrared touch screen. Or add protective glass as needed
Display screens with different optical parameters can be designed according to needs, such as brightness, color gamut, response time, gamma and other parameters, and anti-glare, anti-fingerprint coatings, etc. can also be added
The circuit board we designed can convert the interface of your display into an HDMI interface. If your product does not have any display control capabilities, you can use our serial display and only need to use simple commands to control the displayed content through RS232/458
1.44-inch tft display drawings and interfaces
1.44-inch TN mode tft display, resolution 128×128, backlight 2 LED lights in parallel, working voltage 3.2V, working current 40mA, high brightness display, module brightness 500cd/㎡, using ZIF connector.
The outline drawing is as follows:
Interfaces are defined as follows：
| Pin | Symbol | Detail |
| 1 | LED_A | LED Anode |
| 2 | LED_K | LED Cathode |
| 3 | GND | GRAND |
| 4 | TE | Tearing effect output pin,If not used, please open this pin |
| 5 | CS | Chip select input pin (“Low” enable) |
| 6 | RS | Display data/command selection pin in parallel interface. This pin is used to be serial interface clock. |
| 7 | WR | Write enable in MCU parallel interface Display data/command selection pin in 4-line serial interface. |
| 8 | RD | Read enable in 8080 MCU parallel interface.If not used, please fix this pin at GND. |
| 9 | RESET | Reset Pin |
| 10 | DB0 | Data Bus. |
| 11 | DB1 | |
| 12 | DB2 | |
| 13 | DB3 | |
| 14 | DB4 | |
| 15 | DB5 | |
| 16 | DB6 | |
| 17 | DB7 | |
| 18 | SPI4W | SPI4W=GND: 3-line SPI;SPI4W=IOVCC: 4-line SPI |
| 19 | IM2 | IM0=GND: Serial Interface;IM0=IOVCC: Parallel Interface |
| 20 | IOVCC | Logic Power |
| 21 | VCI | Analog Power |
| 22 | GND | GROUND |
| 23 | INT | TP function pin. |
| 24 | RES | |
| 25 | SCL | |
| 26 | SDA |
